zornnh@musc.edu
| Revision History | ||
|---|---|---|
| Revision 0.04 | 2002-02-28 | Revised by: nhz |
| Revision 0.03 | 2001-09-28 | Revised by: nhz |
| Revision 0.02 | 2001-09-28 | Revised by: KET |
| Revision 0.01 | 2001-09-06 | Revised by: nhz |
With wireless networks and public acces areas it is very easy for an unauthorized user to gain access. Unauthorized users can look for a signal and grab connection information from the signal. Unauthorized users can plug their machine into a public terminal and gain access to the network. Security has been put in place such as WEP, but this security can be subverted with tools like AirSnort. One approach to solving these problems is to not rely on the wireless security features , and instead to place an authentication gateway in front of the wireless network or public access area and force users to authenticate against it before using the network. This HOWTO describes how to set up this gateway with Linux.
This document is copyrighted (c) 2001 Nathan Zorn. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation; with no Invariant Sections, with no Front-Cover Texts, and with no Back-Cover Texts. A copy of the license is available at http://www.gnu.org/copyleft/fdl.html
If you have any questions, please contact <zornnh@musc.edu>
No liability for the contents of this documents can be accepted. Use the concepts, examples and other content at your own risk. As this is a new edition of this document, there may be errors and inaccuracies, that may of course be damaging to your system. Proceed with caution, and although this is highly unlikely, the author(s) do not take any responsibility for that.
All copyrights are held by their by their respective owners, unless specifically noted otherwise. Use of a term in this document should not be regarded as affecting the validity of any trademark or service mark.
Naming of particular products or brands should not be seen as endorsements.
You are strongly recommended to take a backup of your system before major installation and backups at regular intervals.
This is the initial release.
The newest release of this document can be found at http://www.itlab.musc.edu/~nathan/authentication_gateway/. Related HOWTOs can be found at the Linux Documentation Project homepage.
Feedback is most certainly welcome for this document. Without your submissions and input, this document wouldn't exist. Please send your additions, comments and criticisms to the following email address : <zornnh@musc.edu>.
This section describes what is needed for the authentication gateway.
The authentication gateway uses Netfilter and iptables to manage the firewall. Please see the Netfilter HOWTO.
This is a pluggable authentication module (PAM) written by Nathan Zorn that can be found at http://www.itlab.musc.edu/~nathan/pam_iptables.
The authentication gateway will act as the dynamic host configuration protocol (DHCP) server for the public network. It only serves those requesting DHCP services on the public network. I used the ISC DHCP Server .
The gateway can use any means of PAM authentication. The authentication mechanism the Medical University of South Carolina uses is LDAP. Since LDAP was used for authentication, the pam modules on the gateway box were set up to use LDAP. More information can be found at http://www.padl.com/pam_ldap.html. PAM allows you to use many means of authentication. Please see the documentation for the PAM module you would like to use. For more information on other methods, see pam modules.
The gateway box also serves as a DNS server for the public network. I installed Bind, and set it up as a caching nameserver. The rpm package caching-namserver was also used. This package came with Red Hat.
This section describes how to setup each piece of the authentication gateway. The examples used are for a public network in the 10.0.1.0 subnet. eth0 is the interface on the box that is connected to the internal network. eth1 is the interface connected to the public network. The IP address used for this interface is 10.0.1.1. These settings can be changed to fit the network you are using. Red Hat 7.1 was used for the gateway box, so a lot of the examples are specific to Red Hat.
To setup netfilter the kernel must be recompiled to include netfilter support. Please see the Kernel-HOWTO for more information on configuring and compiling your kernel.
This is what my kernel configuration looked like.
# # Networking options # CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set # CONFIG_NETLINK is not set CONFIG_NETFILTER=y CONFIG_NETFILTER_DEBUG=y CONFIG_FILTER=y CONFIG_UNIX=y CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set # CONFIG_IP_PNP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set # CONFIG_INET_ECN is not set # CONFIG_SYN_COOKIES is not set # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=y CONFIG_IP_NF_FTP=y CONFIG_IP_NF_IPTABLES=y CONFIG_IP_NF_MATCH_LIMIT=y CONFIG_IP_NF_MATCH_MAC=y CONFIG_IP_NF_MATCH_MARK=y CONFIG_IP_NF_MATCH_MULTIPORT=y CONFIG_IP_NF_MATCH_TOS=y CONFIG_IP_NF_MATCH_TCPMSS=y CONFIG_IP_NF_MATCH_STATE=y CONFIG_IP_NF_MATCH_UNCLEAN=y CONFIG_IP_NF_MATCH_OWNER=y CONFIG_IP_NF_FILTER=y CONFIG_IP_NF_TARGET_REJECT=y CONFIG_IP_NF_TARGET_MIRROR=y CONFIG_IP_NF_NAT=y CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=y CONFIG_IP_NF_TARGET_REDIRECT=y CONFIG_IP_NF_NAT_FTP=y CONFIG_IP_NF_MANGLE=y CONFIG_IP_NF_TARGET_TOS=y CONFIG_IP_NF_TARGET_MARK=y CONFIG_IP_NF_TARGET_LOG=y CONFIG_IP_NF_TARGET_TCPMSS=y |
iptables needs to be installed. To install iptables either use a package from your distribution or install from source. Once the above options were compiled in the new kernel and iptables was installed, I set the following default firewall rules.
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A INPUT -i eth0 -m state --state NEW, INVALID -j DROP iptables -A FORWARD -i eth0 -m state --state NEW, INVALID -j DROP iptables -I FORWARD -o eth0 -j DROP iptables -I FORWARD -s 10.0.1.0/24 -d 10.0.1.1 -j ACCEPT |
The above commands can also be put in an initscript to start up when the server restarts. To make sure the rules have been added issue the following commands:
iptables -v -t nat -L iptables -v -t filter -L |
To save these rules I used Red Hat's init scripts.
/etc/init.d/iptables save /etc/init.d/iptables restart |
Once the rules are in place turn on IP forwarding by executing this command.
echo 1 > /proc/sys/net/ipv4/ip_forward |
To make sure ip forwarding is enabled when the machine restarts add the following line to /etc/sysctl.conf.
net.ipv4.ip_forward = 1 |
Now the gateway box will be able to do network address translation (NAT), but it will drop all forwarding packets except those coming from within the public network and bound for the gateway.
This module is a PAM session module that inserts the firewall rule needed to allow forwarding for the authenticated client. To set it up simply get the source and compile it by running the following commands.
gcc -fPIC -c pam_iptables.c ld -x --shared -o pam_iptables.so pam_iptables.o |
You should now have two binaries called pam_iptables.so and pam_iptables.o. Copy pam_iptables.so to /lib/security/pam_iptables.so.
cp pam_iptables.so /lib/security/pam_iptables.so |
The chosen authentication client for the gateway was ssh so we added the following line to /etc/pam.d/sshd.
session required /lib/security/pam_iptables.so |
Now, when a user logs in with ssh, the firewall rule will be added.
The default interface for pam_iptables is eth0. This default can be changed by adding the interface parameter.
session required /lib/security/pam_iptables.so interface=eth1 |
This is only needed if the interface name that connects to the external network is not eth0.
To test if the pam_iptables module is working perform the following steps:
Log into the box with ssh.
Check to see if the rule was added with the command iptables -L.
Log out of the box to make sure the rule is removed.
I installed DHCP using the following dhcpd.conf file.
subnet 10.0.1.0 netmask 255.255.255.0 {
# --- default gateway
option routers 10.0.1.1;
option subnet-mask 255.255.255.0;
option broadcast-address 10.0.1.255;
option domain-name-servers 10.0.1.1;
range 10.0.1.3 10.0.1.254;
option time-offset -5; # Eastern Standard Time
default-lease-time 21600;
max-lease-time 43200;
}
|
The server was then run using eth1 , the interface to the public net.
/usr/sbin/dhcpd eth1
|
As indicated in previous sections, I've set this gateway up to use LDAP for authenticating. However, you can use any means that PAM allows for authentication. See Section 2.4 for more information.
In order to get PAM LDAP to authenticate, I installed OpenLDAP and configured it with the following in /etc/ldap.conf.
# Your LDAP server. Must be resolvable without using LDAP. host itc.musc.edu # The distinguished name of the search base. base dc=musc,dc=edu ssl no |
The following files were used to configure PAM to do the LDAP authentication. These files were generated by Red Hat's configuration utility.
#%PAM-1.0
# This file is auto-generated.
# User changes will be destroyed the next time authconfig is run.
auth required /lib/security/pam_env.so
auth sufficient /lib/security/pam_unix.so likeauth nullok
auth sufficient /lib/security/pam_ldap.so use_first_pass
auth required /lib/security/pam_deny.so
account required /lib/security/pam_unix.so
account [default=ok user_unknown=ignore service_err=ignore system_err=ignore] /lib/security/pam_ldap.so
password required /lib/security/pam_cracklib.so retry=3
password sufficient /lib/security/pam_unix.so nullok use_authtok
password sufficient /lib/security/pam_ldap.so use_authtok
password required /lib/security/pam_deny.so
session required /lib/security/pam_limits.so
session required /lib/security/pam_unix.so
session optional /lib/security/pam_ldap.so
|
#%PAM-1.0
auth required /lib/security/pam_stack.so service=system-auth
auth required /lib/security/pam_nologin.so
account required /lib/security/pam_stack.so service=system-auth
password required /lib/security/pam_stack.so service=system-auth
session required /lib/security/pam_stack.so service=system-auth
#this line is added for firewall rule insertion upon login
session required /lib/security/pam_iptables.so debug
session optional /lib/security/pam_console.so
|
I installed the default version of Bind that comes with Red Hat 7.1, and the caching-nameserver RPM. The DHCP server tells the machines on the public net to use the gateway box as their nameserver.
To use the authentication gateway, configure your client machine to use DHCP. Install a ssh client on the box and ssh into the gateway. Once you are logged in, you will have access to the internal network. The following is an example session from a unix based client:
bash>ssh zornnh@10.0.1.1 zornnh's Password: gateway> |
As long as you stayed logged in, you will have access. Once you log out, access will be taken away.
This method of security does not rely on the security provided by the wireless network community. It assumes that the entire wireless network is insecure and outside of your network.
The gateway does not encrypt traffic. It only allows you access to the network behind it. If encryption and authentication are desired, a VPN should be used.
A document describing the NASA implementation of the authentication gateway.
A white paper describing how the University of Alberta created an authentication gateway.
Nocat.net has an authentication gateway for wireless networks. This software has a web based client.
This is just a collection of what I believe are the most common questions people might have. Give me more feedback and I will turn this section into a proper FAQ.